 |
||
| Two magnets attached to a fuel hose | ||
 |
||
| The underside of the magnet | ||
 |
||
| The full length of the magnet with its wrapper |
|
||
| Two magnets attached to a fuel hose | ||
|
||
| The underside of the magnet | ||
|
||
| The full length of the magnet with its wrapper |
Magnetic Enhancement
This is the newest addition to the products we offer. We are using 20mm diameter by 10mm thick neodymium magnets,
with a pulling power of about 6 kg or 13.5 pounds each. The mounting system is simple and basic - its not pretty,
and you will notice that the bottom of the magnet is exposed. This is on purpose. It increases the available amount
of magnetic force directly transmitted to the object that you want to have an effect on. If we were to cover it with
a layer of plastic, as is the usual procedure, we would reduce effectiveness by somewhere around 20%.
And the price? Its $14.50, or £10.25. This is very inexpensive for this kind of application. The cases of the
competition are prettier, and the prices sometimes double, or more - in any case, significantly more expensive, with no
added effectiveness.
The purpose of the case is simply a means of securing the magnet against whatever it is bound. It does that quite well -
and the securing tie can be easily released and it can be remounted.
They can be used on fuel hoses, on the inlet and outlet of the vapor expansion tubes we sell, on boiler gas inlets,
on water pipes - anywhere where an increase in combustion efficiency is sought, or the benefits of ionization are
required. There are too many applications for this to be quoted here. For maximum efficiency - and this is always
recommended - you should mount two near each other. So one is north pole, and one is south pole, on the facing side
next to the tube/pipe/etc. that you are mounting it on. Doesn't matter what order this is in - whether north/south or
south/north. At these prices, buying two is not expensive. If you buy only one - as is the case with many magnetic
improvement devices - you will halve the efficiency. Single pole treatment is limited, if it does anything.
Because of the mounting, the magnets are held in place by their attraction to the metal bits. The attachment wraps
are reusuable - that is, if you wrap it around something, and want to move or remove it, its easy enough to detach
it. The reason we have them mounted as they are, so you can pull the magnet, with some effort, from its mounting,
is so that you can reverse the polarity without having to purchase another magnet.
The only disadvantage of not having a protective bottom is if it is used on hot surfaces. We don't recommend you
using this on anything that is itself near the boiling point of water. The great majority of applications will not
be anywhere near this. One thing to remember - don't put the magnets together! If you do, they will have 26 pounds
of pulling power between them to separate, so you could pinch your skin painfully if it was caught between the two.
In that case, you would have to use a screwdriver to pry them apart - ouch!
What sort of improvements or fuel efficiency savings can you expect? With 4 of them - two on
them on the fuel hose next to each other, as in the picture, and one each on the inlet and outlet of our expansive
tube - opposing poles in each case, we were able to go from 45mpg on our standard intake manifold vaporizer system
to 51mpg. That's a 20% increase! The car before we started doing anything got 30mpg. Our intake manifold vaporizer
with an expansion tube increased mpg by 50%, and with 4 of these magnets as described the efficiency went over 70%.
We have obtained this improvement over and over again - this is not a one off example.
You could just purchase 4 of these - 2 for the fuel line, and 2 on your air intake - without getting anything else,
and expect somewhere in the range of 12-15% increase in mpg. You could do this on any vehicle, without an EFIE or
lambda sensor simulator - and it would work. And take about 5 minutes to install. The increase to 20% is achievable
with our expansion tube in a vaporizer arrangement, because the inlet and outlet constrict all the gases entering
and leaving the expansion tube so they are exposed to the strong magnetic fields from the magnets. One more idea -
you could try these on a water vaporizer, and see if it makes an improvement. We'll give a test, and let you know
on this website.
As with all our products, if after ordering and trying these magnetic enhancers you are not pleased with the results, after returning
them to us we will give you a full refund. This guarantee is for one year from date of purchase. This does not affect your statutory rights.